Search engine for discovering works of Art, research articles, and books related to Art and Culture
ShareThis
Javascript must be enabled to continue!

Formation of Orthogonal Components of Input Signals in Digital Measuring Protection Elements with Correction of Dynamic Errors

View through CrossRef
Digital measuring elements in microprocessor protections of electrical installations are implemented mainly with the use of orthogonal components of input signals. To form orthogonal components in microprocessor protections, digital Fourier filters are most widely used, the action of which is al-ways inertial in transient modes. As a result, a dynamic error appears, changing over time and completely disappearing when a steady-state regime occurs. The dynamic error consists of amplitude and phase errors, which can significantly affect the functioning of digital measuring elements and create conditions for their excessive triggering during external short circuits and deceleration of triggering during internal short circuits. Therefore, it is advisable to compensate for the dynamic error, for which it is proposed to determine the amplitude and phase of the fundamental harmonic signal by specially formed orthogonal components. The proposed method of forming orthogonal components of the signal with compensation of dynamic amplitude and phase errors is based on the use of orthogonal components of the digital Fourier filter, followed by the determination of their samples of the final orthogonal components that coincide with the orthogonal components of Fourier in steady-state mode and shifted in phase relative to the latter in transient mode. The amplitude and phase of the signal with minimal dynamic phase errors are calculated from the samples of the final orthogonal components in the digital measuring element. In the dynamic modeling environment of MATLAB-Simulink-SimPowerSystems, a digital model is implemented, which includes a power system, a three-phase group of current transformers, a load, a short-circuit block, as well as a model of a digital measuring element implemented on the basis of the final orthogonal components. The operation of the digital model was checked using two types of test effects, viz. a sinusoidal signal with a frequency of 50 Hz, and a signal close to the real secondary current of a short-circuit current transformer. As a result of the calculations, it was found that digital measuring elements made on the basis of the proposed methodology made it possible to reduce the relative dynamic amplitude and phase errors by three to four times, as compared with the Fourier measuring element taken as a reference.
Title: Formation of Orthogonal Components of Input Signals in Digital Measuring Protection Elements with Correction of Dynamic Errors
Description:
Digital measuring elements in microprocessor protections of electrical installations are implemented mainly with the use of orthogonal components of input signals.
To form orthogonal components in microprocessor protections, digital Fourier filters are most widely used, the action of which is al-ways inertial in transient modes.
As a result, a dynamic error appears, changing over time and completely disappearing when a steady-state regime occurs.
The dynamic error consists of amplitude and phase errors, which can significantly affect the functioning of digital measuring elements and create conditions for their excessive triggering during external short circuits and deceleration of triggering during internal short circuits.
Therefore, it is advisable to compensate for the dynamic error, for which it is proposed to determine the amplitude and phase of the fundamental harmonic signal by specially formed orthogonal components.
The proposed method of forming orthogonal components of the signal with compensation of dynamic amplitude and phase errors is based on the use of orthogonal components of the digital Fourier filter, followed by the determination of their samples of the final orthogonal components that coincide with the orthogonal components of Fourier in steady-state mode and shifted in phase relative to the latter in transient mode.
The amplitude and phase of the signal with minimal dynamic phase errors are calculated from the samples of the final orthogonal components in the digital measuring element.
In the dynamic modeling environment of MATLAB-Simulink-SimPowerSystems, a digital model is implemented, which includes a power system, a three-phase group of current transformers, a load, a short-circuit block, as well as a model of a digital measuring element implemented on the basis of the final orthogonal components.
The operation of the digital model was checked using two types of test effects, viz.
a sinusoidal signal with a frequency of 50 Hz, and a signal close to the real secondary current of a short-circuit current transformer.
As a result of the calculations, it was found that digital measuring elements made on the basis of the proposed methodology made it possible to reduce the relative dynamic amplitude and phase errors by three to four times, as compared with the Fourier measuring element taken as a reference.

Related Results

NICU Medication Errors: Describing the Cause and Nature of Medication Errors in a NICU in Qatar
NICU Medication Errors: Describing the Cause and Nature of Medication Errors in a NICU in Qatar
IntroductionA medication error can be defined as “any error occurring in the medication use process” and focuses on problems with the delivery of medication to a patient [1]. Medic...
Access Denied
Access Denied
Introduction As social-distancing mandates in response to COVID-19 restricted in-person data collection methods such as participant observation and interviews, researchers turned t...
The influence of micro influencers and digital marketing on product purchasing decisions at tiktok shop in bengkulu city
The influence of micro influencers and digital marketing on product purchasing decisions at tiktok shop in bengkulu city
THE INFLUENCE OF MICRO-INFLUENCERS AND DIGITAL MARKETING ON PURCHASE DECISIONS OF TIKTOK SHOP CUSTOMERS IN BENGKULU CITY Andhes Tiani Putri, Meylaty F   12Faculty Of Economic E...
Improvement of Algorithm for Formation of Orthogonal Components of Input Quantities in Microprocessor Protection
Improvement of Algorithm for Formation of Orthogonal Components of Input Quantities in Microprocessor Protection
The use of orthogonal components (OC) underlies  the construction of measuring elements of  modern protection and automation devices. In most microprocessor-based protections, the ...
Dynamic Properties of Remote Sensing Algorithm in Digital Resistance Elements
Dynamic Properties of Remote Sensing Algorithm in Digital Resistance Elements
In microprocessor-based distance protection of lines, digital resistance elements are used as measuring instruments for determining the components of the input resistance vector an...
Energy and Spectrum of Transient Electromagnetic Responses for Deep-Reading Looking Ahead LWD Tools
Energy and Spectrum of Transient Electromagnetic Responses for Deep-Reading Looking Ahead LWD Tools
The total electromagnetic (EM) fields consist of the primary fields excited and propagated in the background model and the scattering fields reflected from the resistivity anomaly....
7 th International Symposium on Enabling Technologies for Life Sciences (ETP)
7 th International Symposium on Enabling Technologies for Life Sciences (ETP)
The seventh in the series of ETP Symposia (see Rapid Communications in Mass Spectrometry 2012, 26 , ...
Formation of Orthogonal Components of Input Currents in Microprocessor Protections of Electrical Equipment
Formation of Orthogonal Components of Input Currents in Microprocessor Protections of Electrical Equipment
The methods used in the microprocessor protection of electrical equipment for forming orthogonal components of input currents ensure their reliable isolation after changing the mod...

Back to Top