Search engine for discovering works of Art, research articles, and books related to Art and Culture
ShareThis
Javascript must be enabled to continue!

EFFECT OF PUTTY PROPERTIES IN REPAIRING CORRODED PIPELINE: A FINITE ELEMENT ANALYSIS

View through CrossRef
Underground pipelines are the most preferable way to transport oil and gas over a long distance. These steel pipelines often suffered from several deteriorations including corrosion. Corrosion causes the outer lining of a pipeline to thin and subsequently reducing pipeline strength. In order to prevent this loss of strength, repair is required. Composite wrap repair is a technique that can be used to repair damage pipeline. Composite wrap repair consist of Fibre Reinforced Polymer (FRP) composite wrap and putty as infill material to restore the strength of a damaged steel pipe. Recently, there is tendency in reducing the usage of composite wrapping layer due to several reasons. Ultimately, it is hoped that one day the repair can be done without composite wrapping. Thus, the purpose of this research is to explore the potential of using putty alone as a repair material in repairing corroded pipeline without composite wrap via finite element analysis. Difference geometrical defects that simulating external corrosion were investigated to study the influence of defect sizes towards the burst pressure of corroded pipeline. Two infill materials which both have difference mechanical properties are used in this research to investigate their influence towards the performance of the repaired pipes. Finite element analysis has been conducted to determine the behaviour of the defected pipeline with a patch of the infill covered the defected area. The analysis was conducted for three defect sizes: 100mm x 100mm, 75mm x 150mm, and 25mm x 150mm for both putties. It was found that the narrow defect of the pipeline causing the pipe to burst at lower pressure as compared to defect that have the same dimension area for both of the infill material. This may due to high stress concentration at small area of the defect. Furthermore, it was also revealed that infill with higher ultimate tensile strength able to withstand higher pressure. The finding of the research shows that by using appropriate infill, there are potential to increase the burst pressure by about 5%. The findings of this research can serve as stepping stone to study the feasibility of repairing damaged pipeline using putty alone.
Title: EFFECT OF PUTTY PROPERTIES IN REPAIRING CORRODED PIPELINE: A FINITE ELEMENT ANALYSIS
Description:
Underground pipelines are the most preferable way to transport oil and gas over a long distance.
These steel pipelines often suffered from several deteriorations including corrosion.
Corrosion causes the outer lining of a pipeline to thin and subsequently reducing pipeline strength.
In order to prevent this loss of strength, repair is required.
Composite wrap repair is a technique that can be used to repair damage pipeline.
Composite wrap repair consist of Fibre Reinforced Polymer (FRP) composite wrap and putty as infill material to restore the strength of a damaged steel pipe.
Recently, there is tendency in reducing the usage of composite wrapping layer due to several reasons.
Ultimately, it is hoped that one day the repair can be done without composite wrapping.
Thus, the purpose of this research is to explore the potential of using putty alone as a repair material in repairing corroded pipeline without composite wrap via finite element analysis.
Difference geometrical defects that simulating external corrosion were investigated to study the influence of defect sizes towards the burst pressure of corroded pipeline.
Two infill materials which both have difference mechanical properties are used in this research to investigate their influence towards the performance of the repaired pipes.
Finite element analysis has been conducted to determine the behaviour of the defected pipeline with a patch of the infill covered the defected area.
The analysis was conducted for three defect sizes: 100mm x 100mm, 75mm x 150mm, and 25mm x 150mm for both putties.
It was found that the narrow defect of the pipeline causing the pipe to burst at lower pressure as compared to defect that have the same dimension area for both of the infill material.
This may due to high stress concentration at small area of the defect.
Furthermore, it was also revealed that infill with higher ultimate tensile strength able to withstand higher pressure.
The finding of the research shows that by using appropriate infill, there are potential to increase the burst pressure by about 5%.
The findings of this research can serve as stepping stone to study the feasibility of repairing damaged pipeline using putty alone.

Related Results

Installation Analysis of Matterhorn Pipeline Replacement
Installation Analysis of Matterhorn Pipeline Replacement
Abstract The paper describes the installation analysis for the Matterhorn field pipeline replacement, located in water depths between 800-ft to 1200-ft in the Gul...
Evaluating the Surface Properties of Prosthodontic Polymer Impression Materials
Evaluating the Surface Properties of Prosthodontic Polymer Impression Materials
Surface properties of prosthodontic polymer impression materials, such as hardness, roughness, and accuracy, are crucial for the accurate replication of oral structures in restorat...
First Arctic Subsea Pipelines Moving to Reality
First Arctic Subsea Pipelines Moving to Reality
Abstract Two offshore development projects which involve subsea arctic pipelines are being proposed by British Petroleum Exploration (BP). Both projects are locat...
Probability Distribution of Cross-sectional radius of Corroded Steel Bars in Concrete and Its application
Probability Distribution of Cross-sectional radius of Corroded Steel Bars in Concrete and Its application
The impress current method is applied to acquire corroded steel bars embedded in concrete, and three-dimensional(3D) laser scanning techniques are applied on corroded steel bars to...
Development and Use of Simulation Trainers for Pipeline Controllers
Development and Use of Simulation Trainers for Pipeline Controllers
Enbridge is in the forefront of development and application of computer simulation based training systems for Pipeline Controllers. Since 1985, the Pipeline Dynamics section of Enb...
A Fluid-pipe-soil Approach to Stability Design of Submarine Pipelines
A Fluid-pipe-soil Approach to Stability Design of Submarine Pipelines
Abstract The conventional approach to submarine pipeline stability design considers interactions between water and pipeline (fluid-pipe) and pipeline and seabed (...
Pipeline Resistance
Pipeline Resistance
Pipeline resistance is where an often abstract and wonky climate movement meets the bravery and boldness of Indigenous and other frontline defenders of land and water who inspire d...

Back to Top