Search engine for discovering works of Art, research articles, and books related to Art and Culture
Javascript must be enabled to continue!
Superplasticity of coarse-grained Ti-13V-11Cr-3Al alloy
View through CrossRef
Abstract
The superplastic behavior of Ti-13V-11Cr-3Al alloy with beta single phase structure and average grain size of 220 μm was investigated. It was found that elongation increases with temperature at strain rates of 0.1 and 1 s−1. The optimum condition for superplastic deformation of the alloy was achieved in the temperature range 1030–1080°C and with a strain rate of 0.1 s−1. In this condition the amount of elongation reaches 200%. Grain refinement occurred during deformation which can be attributed to the occurrence of dynamic recovery and continuous dynamic recrystallization. In addition, it was seen that in the temperature range 930–1080°C, the strain rate sensitivity parameter (m) was higher than 0.3, which is an appropriate value for superplastic deformation. A high value of m, elongation over 100%, and coarse-grained microstructure of the alloy suggested that superplastic behavior of the Ti-13V-11Cr-3Al alloy can be similar to the behavior of coarse-grained superplastic alloys.
Title: Superplasticity of coarse-grained Ti-13V-11Cr-3Al alloy
Description:
Abstract
The superplastic behavior of Ti-13V-11Cr-3Al alloy with beta single phase structure and average grain size of 220 μm was investigated.
It was found that elongation increases with temperature at strain rates of 0.
1 and 1 s−1.
The optimum condition for superplastic deformation of the alloy was achieved in the temperature range 1030–1080°C and with a strain rate of 0.
1 s−1.
In this condition the amount of elongation reaches 200%.
Grain refinement occurred during deformation which can be attributed to the occurrence of dynamic recovery and continuous dynamic recrystallization.
In addition, it was seen that in the temperature range 930–1080°C, the strain rate sensitivity parameter (m) was higher than 0.
3, which is an appropriate value for superplastic deformation.
A high value of m, elongation over 100%, and coarse-grained microstructure of the alloy suggested that superplastic behavior of the Ti-13V-11Cr-3Al alloy can be similar to the behavior of coarse-grained superplastic alloys.
Related Results
New Evidence for Hydrothermal Sedimentary Genesis of the Ni‐Mo Deposits in Black Rock Series of the Basal Cambrian, Guizhou Province: Discovery of Coarse‐Grained Limestones and its Geochemical Characteristics
New Evidence for Hydrothermal Sedimentary Genesis of the Ni‐Mo Deposits in Black Rock Series of the Basal Cambrian, Guizhou Province: Discovery of Coarse‐Grained Limestones and its Geochemical Characteristics
Abstract:The molybdenum‐nickel deposits in Shuidong District of Nayong County (Guizhou Province, Southwest China) are found mainly in black shale series of Lower Cambrian Niutitang...
Subsurface as a bioreactor : interaction between physical heterogeneity and microbial processes
Subsurface as a bioreactor : interaction between physical heterogeneity and microbial processes
Infiltration systems are water treatment technologies where water vertically percolates through porous media while several biogeochemical processes occur. Biofilms are the main res...
Effect of Ag, In and AgIn Alloying Additions on Microstructure and Texture of Mg-3Al-1Zn Alloy during Multi-Pass Warm Rolling
Effect of Ag, In and AgIn Alloying Additions on Microstructure and Texture of Mg-3Al-1Zn Alloy during Multi-Pass Warm Rolling
In the present investigation the rolling response, microstructure and texture evolution of four Mg alloys during multi-pass warm rolling were evaluated. The nominal composition of ...
Isothermal Oxidation Behaviour of 800H Nickel-Based Alloy
Isothermal Oxidation Behaviour of 800H Nickel-Based Alloy
Abstract
The behaviour of 800H nickel (Ni)-based alloy under isothermal oxidation condition was study in this paper. The isothermal oxidation behaviour was examined ...
Titanium Alloys: Thermomechanical Process Design to Achieve Superplasticity in Bulk Material
Titanium Alloys: Thermomechanical Process Design to Achieve Superplasticity in Bulk Material
Titanium alloys subjected to suitable thermomechanical processing (TMP) schedules can exhibit superplasticity. Most studies on superplasticity of titanium alloys are directed to sh...
Sand properties investigation at Meridiani Planum, Mars
Sand properties investigation at Meridiani Planum, Mars
Granulometry, shape, and chemical composition analyses of the sediments studied by the Opportunity rover along its entire 45-km-long traverse have been used to classify sediments a...
Protocol for the development of coarse-grained structures for macromolecular simulation using GROMACS
Protocol for the development of coarse-grained structures for macromolecular simulation using GROMACS
Coarse-grained simulations have emerged as a valuable tool in the study of large and complex biomolecular systems. These simulations, which use simplified models to represent compl...
In Vitro Comparative Study of Fretting-Corrosion Resistance of Ti6Al4V and Co28Cr6Mo in a Taper Joint Subjected to High Bending Moment
In Vitro Comparative Study of Fretting-Corrosion Resistance of Ti6Al4V and Co28Cr6Mo in a Taper Joint Subjected to High Bending Moment
Co alloy modular necks have been introduced in orthopaedics to address mechanical failure of the neck-stem junction (NSJ) observed in Ti alloy dual-modular hip stem. However, follo...