Search engine for discovering works of Art, research articles, and books related to Art and Culture
Javascript must be enabled to continue!
Fabrication of Indium-Tin Alloy and Oxide Nanowires Using Extrusion Molding Process in the Air
View through CrossRef
A simple method to indium tin alloy and oxide nanowires were achieved by using the extrusion molding process in the air. Eutectic indium tin bulk were firstly injected into AAO templates. After dissolving AAO, the indium tin nanowires were collected in ethanol. Furthermore, in order to have oxide nanowires, alloy nanowires were directly oxidized by heat treatment in the air below its melting point for 24 hours. Finally, crystalline indium-tin oxide and indium oxide nanowires with diameters 90-110 nm and lengths 2-20 μm were obtained.
Trans Tech Publications, Ltd.
Title: Fabrication of Indium-Tin Alloy and Oxide Nanowires Using Extrusion Molding Process in the Air
Description:
A simple method to indium tin alloy and oxide nanowires were achieved by using the extrusion molding process in the air.
Eutectic indium tin bulk were firstly injected into AAO templates.
After dissolving AAO, the indium tin nanowires were collected in ethanol.
Furthermore, in order to have oxide nanowires, alloy nanowires were directly oxidized by heat treatment in the air below its melting point for 24 hours.
Finally, crystalline indium-tin oxide and indium oxide nanowires with diameters 90-110 nm and lengths 2-20 μm were obtained.
Related Results
Metallography and Microstructures of Tin and Tin Alloys
Metallography and Microstructures of Tin and Tin Alloys
Abstract
This article describes the specimen preparation steps for tin and tin alloys, and for harder base metals which are coated with these materials with illustra...
Indium and Indium Compounds
Indium and Indium Compounds
AbstractIndium is a very soft, silvery metal and its abundance is about 0.05 ppm in the earth's crust. It is widely distributed, but never in concentrations high enough to justify ...
A Preliminary Review of Metallogenic Regularity of Tin Deposits in China
A Preliminary Review of Metallogenic Regularity of Tin Deposits in China
China is rich in tin resources, and contains many types of tin deposits. Among the tin deposit types, the cassiterite‐sulfide type, skarn type and quartz vein type occupy a large p...
Adsorption effect of oxygen on ZnO Nanowires (100 nm) leading towards pronounced edge effects and voltage enhancement
Adsorption effect of oxygen on ZnO Nanowires (100 nm) leading towards pronounced edge effects and voltage enhancement
Abstract
Here, we report high output piezoelectric voltage generation from oxidized ZnO nanowires (100 nm). Periodic high output voltage peaks were observed during s...
Reliability Assessment of Indium Micro Bumps for 2.5D/3D Electronic Packaging Through Cryo-Argon Milling Technique
Reliability Assessment of Indium Micro Bumps for 2.5D/3D Electronic Packaging Through Cryo-Argon Milling Technique
Indium bumps are widely used in electronic packaging for interconnecting microelectronic devices due to their low melting point of 156.6 degrees C, excellent bonding capabilities a...
On-chip fabrication of lateral growth ZnO nanowire array UV sensor
On-chip fabrication of lateral growth ZnO nanowire array UV sensor
In this paper, we integrate nano technology into traditional microelectronic processing, and develop an on-chip UV sensor based on lateral growth ZnO nanowire arrays. Traditional p...
Fundamentals of Extrusion
Fundamentals of Extrusion
Abstract
This chapter introduces basic extrusion concepts, including types, processes, mechanics, and the principal variables and their effects on extrusion. The cha...
Internal Oxidation Behavior of Fe-33Ni-19Cr Alloy
Internal Oxidation Behavior of Fe-33Ni-19Cr Alloy
Fe-33Ni-19Cr alloy is the Ni-based alloy used at high temperature condition due to its excellent ability to form protective oxide layer at high temperature. Fe-33Ni-19Cr alloy was ...