Javascript must be enabled to continue!
Late Quaternary Activity: Kouma Fault
View through CrossRef
The Kouma Fault, located at the northern foot of the Mangshan Mountain in Luoyang City, Henan Province, China, is an active fault newly discovered in the field seismic geological survey. The Kouma Fault is a normal fault that is approximately 30 km in length, near the east-west strike, and the north dip. The study on the nature of the Quaternary activity of the Kouma Fault is of great significance to the potential seismic source zone division, urban and rural land planning, site selection for major projects, the assessment and prevention of earthquake disaster risk. Through a series of seismic geological surveys, 12 fault outcrops were discovered, which were all distributed on the slopes of the loess gullies. The Kouma Fault cuts loess, clay, sand, and gravel. The fault planes and scratch can be seen clearly. The filling in the fault zone is dominated by clay, loess, and pebbles, among others. When the width of the fault zone is smaller (10–30 cm), most clay in the zone is laminated in occurrence. The laminated surface is almost parallel to the fault plane and the long axis direction of pebbles in the fault zone is almost parallel to the fault plane. When the width of the fault zone is greater (for instance, 1.6 m), the clay and loess in the fault zone are massive. The composite drilling geological section and trench reveal two paleoseismic events of the Kouma Fault, the paleoseismic event I occurred at the fault in the Middle Pleistocene; the paleoseismic event II occurred at the fault in the later period of the Late Pleistocene, and the vertical offset of the upper Pleistocene bottom boundary is 13.57 m. Based on the OSL age data in the fault G1 outcrop of the fault and TC1 and TC2 trenches, the latest activity age of the Kouma Fault may be defined within the range of (38.84 ± 4.69) to (40.90 ± 4.45) kaB.P. The latest active age of the Kouma fault is the late of Late Pleistocene. The average vertical slip rate of the fault during the Late Pleistocene has been 0.11 mm/a.
Frontiers Media SA
Title: Late Quaternary Activity: Kouma Fault
Description:
The Kouma Fault, located at the northern foot of the Mangshan Mountain in Luoyang City, Henan Province, China, is an active fault newly discovered in the field seismic geological survey.
The Kouma Fault is a normal fault that is approximately 30 km in length, near the east-west strike, and the north dip.
The study on the nature of the Quaternary activity of the Kouma Fault is of great significance to the potential seismic source zone division, urban and rural land planning, site selection for major projects, the assessment and prevention of earthquake disaster risk.
Through a series of seismic geological surveys, 12 fault outcrops were discovered, which were all distributed on the slopes of the loess gullies.
The Kouma Fault cuts loess, clay, sand, and gravel.
The fault planes and scratch can be seen clearly.
The filling in the fault zone is dominated by clay, loess, and pebbles, among others.
When the width of the fault zone is smaller (10–30 cm), most clay in the zone is laminated in occurrence.
The laminated surface is almost parallel to the fault plane and the long axis direction of pebbles in the fault zone is almost parallel to the fault plane.
When the width of the fault zone is greater (for instance, 1.
6 m), the clay and loess in the fault zone are massive.
The composite drilling geological section and trench reveal two paleoseismic events of the Kouma Fault, the paleoseismic event I occurred at the fault in the Middle Pleistocene; the paleoseismic event II occurred at the fault in the later period of the Late Pleistocene, and the vertical offset of the upper Pleistocene bottom boundary is 13.
57 m.
Based on the OSL age data in the fault G1 outcrop of the fault and TC1 and TC2 trenches, the latest activity age of the Kouma Fault may be defined within the range of (38.
84 ± 4.
69) to (40.
90 ± 4.
45) kaB.
P.
The latest active age of the Kouma fault is the late of Late Pleistocene.
The average vertical slip rate of the fault during the Late Pleistocene has been 0.
11 mm/a.
Related Results
Integration Techniques of Fault Detection and Isolation Using Interval Observers
Integration Techniques of Fault Detection and Isolation Using Interval Observers
An interval observer has been illustrated to be a suitable approach to detect and isolate faults affecting complex dynamical industrial systems.
Concerning fault detection, interv...
Decomposition and Evolution of Intracontinental Strike‐Slip Faults in Eastern Tibetan Plateau
Decomposition and Evolution of Intracontinental Strike‐Slip Faults in Eastern Tibetan Plateau
Abstract:Little attention had been paid to the intracontinental strike‐slip faults of the Tibetan Plateau. Since the discovery of the Longriba fault using re‐measured GPS data in 2...
Evaluating the Science to Inform the Physical Activity Guidelines for Americans Midcourse Report
Evaluating the Science to Inform the Physical Activity Guidelines for Americans Midcourse Report
Abstract
The Physical Activity Guidelines for Americans (Guidelines) advises older adults to be as active as possible. Yet, despite the well documented benefits of physical a...
Structural Characteristics and Evolution Mechanism of Paleogene Faults in the Central Dongying Depression, Bohai Bay Basin
Structural Characteristics and Evolution Mechanism of Paleogene Faults in the Central Dongying Depression, Bohai Bay Basin
Abstract
This study used the growth index, fault activity rate and fault distance burial depth curve methods to analyze the characteristics of fault activity in the central...
Low-temperature thermochronology of fault zones
Low-temperature thermochronology of fault zones
<p>Thermal signatures as well as timing of fault motions can be constrained by thermochronological analyses of fault-zone rocks (e.g., Tagami, 2012, 2019).&#1...
Permeability models for carbonate fault cores
Permeability models for carbonate fault cores
<p>The present contribution focuses on carbonates fault cores exposed in central and southern Italy, which crosscut Mesozoic limestones and dolostones, pertain to 10&...
Data-driven Fault Diagnosis for Cyber-Physical Systems
Data-driven Fault Diagnosis for Cyber-Physical Systems
The concept of Industry 4.0 uses cyber-physical systems and the Internet of Things to create "smart factories" that enable automated and connected production. However, the complex ...
Correlation between the deformation of mineral crystal structures and fault activity: A case study of the Yingxiu-Beichuan fault and the Milin fault
Correlation between the deformation of mineral crystal structures and fault activity: A case study of the Yingxiu-Beichuan fault and the Milin fault
Abstract
The build-up and occurrence of earthquakes are due to the accumulation and release of stress in fault zones. When subjected to tectonic extrusion stress, th...

