Search engine for discovering works of Art, research articles, and books related to Art and Culture
ShareThis
Javascript must be enabled to continue!

Effect of Silicon and Chromium Additions on Surface Oxide/Nitride Layers in a Fe-0.4 wt.% C Alloy by Novel Salt-Bath Nitrocarburizing Treatment

View through CrossRef
Abstract A novel salt-bath nitrocarburizing process recently developed forms a lithium-iron compound-oxide layer on the surface of steel in concurrence with a nitride layer by adding lithium ions to the molten salt. This process has already been successfully applied to mass-produced products. However, the microstructure and its formation process of the surface layer in alloyed steels during the nitrocarburizing process have not yet been fully understood. In this study, we focus on the effect of Si and Cr, which are included in a common die steel, on the microstructure of an oxide layer of a nitrocarburized alloy. The alloys used in this study are Fe-0.4wt%C, Fe-0.4wt%C-2.0wt%Si, and Fe-0.4wt%C-2.0wt%Cr. These alloys were arc melted into button ingots under an Ar atmosphere. The ingots were annealed at 1123 K for 1.0 h, followed by air cooling and double tempering at 873 K, similar to the heat treatments employed to hot-die steels. Salt-bath nitrocarburizing was carried out at 823 K for 0.1-10 h. The microstructures of the cross-sectional surface layers of the samples were examined using an optical microscope and FE-SEM. Elemental mapping as well as phase identification of the surface layers were done by EDS, XRD, and GD-OES. In the Fe-C binary alloy, a thin continuous oxide layer of α-LiFeθ2 formed first on the outermost surface, and a thick iron nitride layer developed underneath the oxide layer, with aligned oxide particles along the grain boundaries of the nitrogen compound layer. In the case of Si addition, the outermost oxide layer became thinner and an additional oxide layer consisting of α-LiFeθ2 and (Li,Fe)3Siθ4 formed between the outer oxide layer and nitrogen compound layer, and the formation of the oxide particles in the nitrogen compound layer was fully suppressed. In the case of Cr addition, internal oxide particles formed in the nitrogen compound layer, similar to those in the binary steel, although an continuous oxide layer of CrfN,O) formed in between those layers. On the basis of these results, the inner oxide layer formed with Si addition contributes to improving the frictional wear characteristics in die steels.
Title: Effect of Silicon and Chromium Additions on Surface Oxide/Nitride Layers in a Fe-0.4 wt.% C Alloy by Novel Salt-Bath Nitrocarburizing Treatment
Description:
Abstract A novel salt-bath nitrocarburizing process recently developed forms a lithium-iron compound-oxide layer on the surface of steel in concurrence with a nitride layer by adding lithium ions to the molten salt.
This process has already been successfully applied to mass-produced products.
However, the microstructure and its formation process of the surface layer in alloyed steels during the nitrocarburizing process have not yet been fully understood.
In this study, we focus on the effect of Si and Cr, which are included in a common die steel, on the microstructure of an oxide layer of a nitrocarburized alloy.
The alloys used in this study are Fe-0.
4wt%C, Fe-0.
4wt%C-2.
0wt%Si, and Fe-0.
4wt%C-2.
0wt%Cr.
These alloys were arc melted into button ingots under an Ar atmosphere.
The ingots were annealed at 1123 K for 1.
0 h, followed by air cooling and double tempering at 873 K, similar to the heat treatments employed to hot-die steels.
Salt-bath nitrocarburizing was carried out at 823 K for 0.
1-10 h.
The microstructures of the cross-sectional surface layers of the samples were examined using an optical microscope and FE-SEM.
Elemental mapping as well as phase identification of the surface layers were done by EDS, XRD, and GD-OES.
In the Fe-C binary alloy, a thin continuous oxide layer of α-LiFeθ2 formed first on the outermost surface, and a thick iron nitride layer developed underneath the oxide layer, with aligned oxide particles along the grain boundaries of the nitrogen compound layer.
In the case of Si addition, the outermost oxide layer became thinner and an additional oxide layer consisting of α-LiFeθ2 and (Li,Fe)3Siθ4 formed between the outer oxide layer and nitrogen compound layer, and the formation of the oxide particles in the nitrogen compound layer was fully suppressed.
In the case of Cr addition, internal oxide particles formed in the nitrogen compound layer, similar to those in the binary steel, although an continuous oxide layer of CrfN,O) formed in between those layers.
On the basis of these results, the inner oxide layer formed with Si addition contributes to improving the frictional wear characteristics in die steels.

Related Results

Stability of Iodine in Differently Iodised Salts
Stability of Iodine in Differently Iodised Salts
Iodine deficiency is a public health problem worldwide. Iodization of salt is a valuable technique to overcome iodine insufficiency. There are, however, problems in uniform iodizat...
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v1
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v1
Modern plant tissues are often processed for phytolith analysis. They represent a fundamental source of comparison for archeological and palaeoenvironmental phytolith assemblages; ...
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v2
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v2
Modern plant tissues are often processed for phytolith analysis. They represent a fundamental source of comparison for archeological and palaeoenvironmental phytolith assemblages; ...
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v1
Phytolith extraction and counting procedure for modern plant material rich in silica skeletons v1
Modern plant tissues are often processed for phytolith analysis. They represent a fundamental source of comparison for archeological and palaeoenvironmental phytolith assemblages; ...
Comparative study of conservative management of anal fissure with warm sitz bath and warm sitz shower bath
Comparative study of conservative management of anal fissure with warm sitz bath and warm sitz shower bath
Background: Conservative treatment of anal fissure encompasses sitz bath as the prime modality. The present study was conducted to evaluate the comparative outcome of warm sitz bat...
Deformation of Allochthonous Salt and Evolution of Related Salt-Structural Systems, Eastern Louisiana Gulf Coast
Deformation of Allochthonous Salt and Evolution of Related Salt-Structural Systems, Eastern Louisiana Gulf Coast
Abstract Salt tectonics in the northern Gulf of Mexico involves both vertical diapirism and lateral silling or flow of salt into wings and tablets (sheets). Combi...
The Political Economy of Salt Imports in Indonesia
The Political Economy of Salt Imports in Indonesia
The use of salt is wide, including in the chemical industry, various foods and beverages, pharmaceuticals and cosmetics. The decision to import salt is aimed at protecting the sust...
Chromium, Molybdenum, and Tungsten
Chromium, Molybdenum, and Tungsten
AbstractThe physical and chemical characteristics of chromium and some of its compounds are summarized.The termchromiumis derived from the Greek word for color, because most chromi...

Back to Top