Javascript must be enabled to continue!
Transistor Coil Ignition System for Kick Start Based Small Engines
View through CrossRef
<div class="section abstract"><div class="htmlview paragraph">Two wheeler 4-stroke small Engine with Kick Start requires longer spark duration along with better spark energy in order to burn the lean mixture and to have better Start ability, lower trigger start RPM is also important to enable ease of start. An effective Ignition System needs to be designed for the above purpose. Hence Transistor Controlled Ignition/Inductive Discharge System (TCI/IDI) unit is preferred which gives all the above mentioned requirements.</div><div class="htmlview paragraph">Normally any conventional TCI/IDI operated 4-stroke two wheelers will have D.C power line align with a Power Source for its operation. The 2 Wheeler Kick start version cannot afford the DC Power Source due to Cost, Hence the Electrical System will not have the DC Power Line. So it is not possible to operate a Conventional TCI/IDI system as it is DC Power based System. The challenge is to operate the TCI/IDI ignition unit without DC Power Source i.e. using AC Source.</div><div class="htmlview paragraph">In order to prove the above concept extensive data were collected on the charging pattern and power consumption during operation of various loads with existing charging system. Based on the collected data and customer usage pattern, appropriate power requirement characteristic graphs are obtained. Hence New TCI/IDI has been designed with longer Spark duration and Less Trigger Start RPM. Finally proto parts are developed as per the required power characteristic and then the system was tested on proto engines.</div><div class="htmlview paragraph">This new system<b>*</b> delivers the attributes of a TCI/IDI ignition unit required for a 4-stroke two wheeler engine without using a DC Power Source i.e. only Kick Start. This is having a huge impact on the reduction of Vehicle electrical system cost as DC Power Source is one of the major cost driver for any electrical system with IDI/TCI ignition unit for better performance. Hence it increases the effective efficiency than Conventional Ignition System designed for Kick Start based small Engines.</div></div>
Society of Automotive Engineers of Japan
Title: Transistor Coil Ignition System for Kick Start Based Small Engines
Description:
<div class="section abstract"><div class="htmlview paragraph">Two wheeler 4-stroke small Engine with Kick Start requires longer spark duration along with better spark energy in order to burn the lean mixture and to have better Start ability, lower trigger start RPM is also important to enable ease of start.
An effective Ignition System needs to be designed for the above purpose.
Hence Transistor Controlled Ignition/Inductive Discharge System (TCI/IDI) unit is preferred which gives all the above mentioned requirements.
</div><div class="htmlview paragraph">Normally any conventional TCI/IDI operated 4-stroke two wheelers will have D.
C power line align with a Power Source for its operation.
The 2 Wheeler Kick start version cannot afford the DC Power Source due to Cost, Hence the Electrical System will not have the DC Power Line.
So it is not possible to operate a Conventional TCI/IDI system as it is DC Power based System.
The challenge is to operate the TCI/IDI ignition unit without DC Power Source i.
e.
using AC Source.
</div><div class="htmlview paragraph">In order to prove the above concept extensive data were collected on the charging pattern and power consumption during operation of various loads with existing charging system.
Based on the collected data and customer usage pattern, appropriate power requirement characteristic graphs are obtained.
Hence New TCI/IDI has been designed with longer Spark duration and Less Trigger Start RPM.
Finally proto parts are developed as per the required power characteristic and then the system was tested on proto engines.
</div><div class="htmlview paragraph">This new system<b>*</b> delivers the attributes of a TCI/IDI ignition unit required for a 4-stroke two wheeler engine without using a DC Power Source i.
e.
only Kick Start.
This is having a huge impact on the reduction of Vehicle electrical system cost as DC Power Source is one of the major cost driver for any electrical system with IDI/TCI ignition unit for better performance.
Hence it increases the effective efficiency than Conventional Ignition System designed for Kick Start based small Engines.
</div></div>.
Related Results
Biomechanical Analysis of Mawashi-Geri Kick Motion on Kenshi Shorinji Kempo Jambi Province
Biomechanical Analysis of Mawashi-Geri Kick Motion on Kenshi Shorinji Kempo Jambi Province
In randori Shorinji Kempo, various variations of attacks are used to get a high number of scores. Mawashi-Geri is the kick most often used by kenshi. Mawashi-Geri has the privilege...
Probabilistic Models for Kick Tolerance
Probabilistic Models for Kick Tolerance
Abstract
Kick tolerance is an evaluation of how large kick sizes i.e. kick volumes an open hole section can withstand without threatening the formation integrity at ...
Study on the image recognition of ammonia ignition process induced by methanol micro-jet
Study on the image recognition of ammonia ignition process induced by methanol micro-jet
<div class="section abstract"><div class="htmlview paragraph">Ammonia is regarded as a possible carbon-free energy source for engines, drawing more and more attention. ...
Promoted Ignition Testing of Metallic Filters in High-Pressure Oxygen
Promoted Ignition Testing of Metallic Filters in High-Pressure Oxygen
Abstract
Currently, no test standard exists for evaluating the ignition tolerance and fault tolerance of metallic filters in high-pressure oxygen. Filters are a crit...
Promoted Ignition Testing of Metallic Filters in High-Pressure Oxygen
Promoted Ignition Testing of Metallic Filters in High-Pressure Oxygen
Currently, no test standard exists for evaluating the ignition tolerance and fault tolerance of metallic filters in high-pressure oxygen. Filters are a critical component in oxygen...
Current control and tuning in a closed HTS coil
Current control and tuning in a closed HTS coil
Up to today, a coil made of high temperature superconductor (HTS) usually needs a soldered joint to form a closed circuit. It is very difficult to have the joint fully superconduct...
Arrhenius type empirical ignition delay equations based on the phenomenology of in-cylinder conditions for wide operating ranges in modern diesel engines
Arrhenius type empirical ignition delay equations based on the phenomenology of in-cylinder conditions for wide operating ranges in modern diesel engines
Ignition delays were systematically measured in a DI diesel engine under wide ranging and various engine operating conditions, including engine speeds, fuel injection pressures, in...
Design 3D Printed Coils for WPT
Design 3D Printed Coils for WPT
Abstract
The geometric shapes of coils influence the performance of a 3D IPT system. In this paper, we proposed a 3D coil design method based on (3D) printing electr...

