Javascript must be enabled to continue!
Optimisation of Sunflower Husk Ash-Activated Slag Binder
View through CrossRef
This study presents the optimisation of an alkali-activated binder produced from ground granulated blast furnace slag (GGBFS) and potassium-rich sunflower husk ash (SHA), by varying SHA content, curing regime, and mixing procedure. Both materials are locally available in the Republic of Serbia. The influence of SHA content (15%, 25%, and 35% by mass of GGBFS) and curing conditions (ambient and 65 °C) on hydration products, workability, and compressive strength was examined. The water-to-binder ratio and GGBFS content were kept constant, and a one-part alkali activation approach was employed using untreated SHA. Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were performed on paste samples, after 2, 7 and 28 days of curing, while workability and compressive strength of mortars were measured after 7 and 28 days. Increasing SHA content enhanced the formation of C-S-H and C-A-S-H gels, resulting in a consistent rise in compressive strength, from 26.6 MPa to 36.2 MPa after 7 days and from 46.2 MPa to 55.1 MPa after 28 days of ambient curing. Workability was slightly reduced with increasing SHA content, resulting in flow diameters of 156.04 mm (15% SHA), 154.10 mm (25% SHA) and 152.76 mm (35% SHA). Curing at 65 °C accelerated early strength gain for 33% to 39% but produced lower 28-day strengths than ambient curing. Additionally, for the optimal mix, SHA was also pre-immersed in water for varying durations to assess its effect on workability, compressive strength, and potassium ion leaching. This pretreatment increased compressive strength by up to 14.7%, depending on immersion time, but reduced workability by up to 15.5%. The novelty of the research is reflected in attaining the highest 28-day compressive strength of 55 MPa (for 25% SHA by mass of GGBFS), under ambient curing, without SHA pretreatment or immersion, highlighting the potential for low-energy, sustainable binder systems using agricultural and industrial by-products.
Title: Optimisation of Sunflower Husk Ash-Activated Slag Binder
Description:
This study presents the optimisation of an alkali-activated binder produced from ground granulated blast furnace slag (GGBFS) and potassium-rich sunflower husk ash (SHA), by varying SHA content, curing regime, and mixing procedure.
Both materials are locally available in the Republic of Serbia.
The influence of SHA content (15%, 25%, and 35% by mass of GGBFS) and curing conditions (ambient and 65 °C) on hydration products, workability, and compressive strength was examined.
The water-to-binder ratio and GGBFS content were kept constant, and a one-part alkali activation approach was employed using untreated SHA.
Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were performed on paste samples, after 2, 7 and 28 days of curing, while workability and compressive strength of mortars were measured after 7 and 28 days.
Increasing SHA content enhanced the formation of C-S-H and C-A-S-H gels, resulting in a consistent rise in compressive strength, from 26.
6 MPa to 36.
2 MPa after 7 days and from 46.
2 MPa to 55.
1 MPa after 28 days of ambient curing.
Workability was slightly reduced with increasing SHA content, resulting in flow diameters of 156.
04 mm (15% SHA), 154.
10 mm (25% SHA) and 152.
76 mm (35% SHA).
Curing at 65 °C accelerated early strength gain for 33% to 39% but produced lower 28-day strengths than ambient curing.
Additionally, for the optimal mix, SHA was also pre-immersed in water for varying durations to assess its effect on workability, compressive strength, and potassium ion leaching.
This pretreatment increased compressive strength by up to 14.
7%, depending on immersion time, but reduced workability by up to 15.
5%.
The novelty of the research is reflected in attaining the highest 28-day compressive strength of 55 MPa (for 25% SHA by mass of GGBFS), under ambient curing, without SHA pretreatment or immersion, highlighting the potential for low-energy, sustainable binder systems using agricultural and industrial by-products.
Related Results
Response of maize to coconut husk ash application in an acid sandy-loam soil in Abakaliki, South-East Nigeria
Response of maize to coconut husk ash application in an acid sandy-loam soil in Abakaliki, South-East Nigeria
Response of maize to coconut husk ash application was evaluated in an acid sandy loam soil under Abakaliki agroecology in South-East Nigeria. A land area measuring 0.03 ha was used...
Sunflower Broomrape (
Orobanche cumana
Wallr.) and Weeds in Sunflower Crops with Minimized Tillage in a Steppe Ecotype Crop Rotation
Sunflower Broomrape (
Orobanche cumana
Wallr.) and Weeds in Sunflower Crops with Minimized Tillage in a Steppe Ecotype Crop Rotation
Abstract
An important reserve for increasing the productivity of agricultural production is a scientifically based crop structure and the use...
Estimate of service life of concrete structures in marine environment
Estimate of service life of concrete structures in marine environment
Deterioration and distress of concrete structures in service is a result of a variety of physicochemics processes. These processes include attack by acids or alkalis, cycles of wet...
Adhesive Behaviour of BOF Slag to BOF Lining Refractory in Slag Splashing Process
Adhesive Behaviour of BOF Slag to BOF Lining Refractory in Slag Splashing Process
A slag layer is formed when slag is splashed onto refractory lining in BOF slag splashing process. The melting temperature of the slag layer and the adhesion of the slag layer to t...
POTENSI SLAG NIKEL HALUS (FeNi 4) PT. ANTAM POMALAA SEBAGAI AGREGAT HALUS PADA CAMPURAN ASPAL
POTENSI SLAG NIKEL HALUS (FeNi 4) PT. ANTAM POMALAA SEBAGAI AGREGAT HALUS PADA CAMPURAN ASPAL
ABSTRAKSlag nikel (FeNi4) adalah jenis terbaru dengan ukuran butiran mendekati pasir (lolos No. 8). Jumlah buangan slag nikel telah mencapai 1 juta ton pada tahun 2018, sehingga be...
Analysis of the Phase Composition and Microstructure of Slag from a Semi-Steel Converter
Analysis of the Phase Composition and Microstructure of Slag from a Semi-Steel Converter
To clarify the phase composition, microstructural characteristics, and phosphorus retention mechanisms of semi-steel converter slag, this study employed characterization techniques...
Quaternary volcanic ash of Kharkiv region
Quaternary volcanic ash of Kharkiv region
Formulation of the problem. The article is devoted to detail geological and mineralogical description of quaternary volcanic ash in Kharkiv region.
The purpose of the article is t...
Effects of chickpea husk on the baking properties of chapattis
Effects of chickpea husk on the baking properties of chapattis
Chickpea husks were extracted by non-alkaline aqueous extraction process and then ground in flour mill. The unextracted husks were also ground in flour mill. The analysis of chickp...

